1. <dd id="ag7t8"><track id="ag7t8"></track></dd>

    <button id="ag7t8"><object id="ag7t8"><input id="ag7t8"></input></object></button>
  2. <rp id="ag7t8"></rp>

          1. <dd id="ag7t8"><pre id="ag7t8"></pre></dd>

            <rp id="ag7t8"></rp>
             
             
            网站首页 公司简介 新品推荐 产品展示 新闻中心 人才招聘 信息反馈 联系我们 友情链接  
            flash2
            反馈:

            滚动文字

             
             
            无锡市华通液压气动制造有限公司
            地址:无锡市东北塘镇农垻村农石路杨家桥
            联系人:朱先生  13906198250
            电 话:0510-88201238、88203666
            传 真:0510-88700320
            网 址:www.blogkoukoku.com 
             
             您当前位置:墙板机首页>新闻中心

            隔墙板机的使用和操作

            作者:匿名    访问量:2055    发布时间:2013/8/27

                  墙板机运行前的检查准备,场地清理与涂刷隔离剂。隔离剂由用户自购,应选用无毒无臭、无刺激、隔离效果良好、对台面和制品无腐蚀且价格低廉的隔离剂,以防止制品与场地表面粘结,起板困难。   

                  检查并调整成型腔尺寸。振动板应处于自由状态,四边与周围部件应有1.5~2.5mm间隙,高度位置比成型刮板的前端底1.5~2mm;成型刮板至墙板底面的高度;前端(与振动板相接处)59mm,后端58mm;   

                  将隔墙板机拉入工位,两前轮内侧分别卡在两地条的外侧,左右墙板的最后端分别也卡在两地条的外测,将挤压机调整至工作状态。   

                  检查各紧固部分是否松动(特别是前后支板螺栓和电气系统的螺栓应重点检查),检查减速箱的油面并使之符合要求;料斗内不得有杂物,向振动导杆上的黄油嘴压黄油;开启电源总开关,启动主电机搅刀旋转。   

                  启动隔墙板机主电机、驱动搅刀空运转,若有异常现象应立即停机检查。注意空载状态切勿启动振动器,以免造成零部件损坏。

             

            我公司专业生产销售墙板机钢棉机 本文由www.blogkoukoku.com提供  

             

            Inspection of the preparation before operation, site clearance from the coating agent. Isolation agent since the purchase by the user, should choose non-toxic, odourless, no stimulation, isolation effect is good, no corrosion and low cost of mesa and products isolation agent, in order to prevent the products and the ground surface bonding, difficulties on board. Check and adjust the cavity size. Vibrating plate should be in free state, the edges with the surrounding parts should be 1.5 ~ 2.5 mm gap, high position than the front end of the molding scraper bottom 1.5 ~ 2 mm; Molding scraper to the height of the wall base; The front (place) and vibration plate 59 mm, back-end 58 mm; The partition plate to pull into the station, the two front wheel inside card is on the outer edge of the article both respectively, about the last end of the wallboard were also in both of the outer, adjust extruder to working condition. Check whether the fastening parts is loose (especially the plate before and after bolt and electrical system should focus on check), inspecting the oil level of the reducer and make it conform to the requirements; Inside the hopper can not have sundry, to guide rod vibration on the nozzle pressure of butter; Open the power master switch, start the main motor mixing blade rotation. Start the partition plate main motor, drive mixing blade idle running, if any abnormal phenomenon should immediately stop check. Pay attention to the light condition do not start the vibrator, lest cause damage of components.

             

            网站首页 | 公司简介 | 新品推荐 | 产品展示 | 新闻中心 | 人才招聘 | 信息反馈 | 联系我们 | 友情链接

            抗震支架 LED显示屏 智慧灯杆 卧式球磨机 粉末冶金 金卡纸 模袋 刮泥机 异型钢管 直读光谱仪 空调风机 清洗机 尾矿 活塞环 麻辣海鲜 高效过滤器 液压系统 搅拌球磨机 端面铣床

            版权所有:无锡市华通液压气动制造有限公司   无锡网站建设:无锡速联科技
            友情链接: 伺服油缸  电机换热器  太阳能污水处理设备 一体化预制泵站

            h无码精品动漫在线观看免费_西西人体大胆444www_国产成人凹凸视频在线观看_被下春药爽到高潮的视频